And this video, you will learn how to define and assign loads to the structure.
So from Lortab go to load cases, you can see that Tekla has defined by default several loads, including
the weight of the numbers and slabs, which is automatically calculated.
I will delete the service load and keep that Adlard and also modify the impossible to separate loads
for offices, residential parking and roof.
You can add new law with the corresponding parameters.
Now, I will validate the model.
Now, to assign the Lords to the model, you may see all the buttons disabled, and that's because we
didn't choose any lower case.
So first, from down below, I will choose the good Lord and I will apply.
I love the Lord and this command will apply the Lord to all Slavs and the selected lover.
Now, from properties window, I would assert the value of below two kilometres per square and I will
select the levels and GraphicLy no mind if you can't see the laws, GraphicLy, you can show from the
scene Condon's and also you can select Alcalde and modify it from the properties window again.
Now, I will assume the roof and post the old three kilometre in the square meters and I will apply
to the roof.
Now for the residential imposed lord, I will assume also three kilometers per square meter.
For the officers, that will be four kilometer per square meter.
For the parking lot will be six km per square meter.
Now for the soil pressure, we need a valiant load, so I will use the insult from Lortab, from the
property's window, I will assume the load on top will be zero and the load on bottom will be one kilometer
per square meter.
Well, make sure that you choose the right direction for the world.
So in my case, it's global that.
Now, I will define a new load to assign the partition laws for the slabs.
And I will choose the perimeter, Lourdes, from Lortab, this will apply a linear load around the perimeter
of a certain slab.
You may notice that the ground floor and the roof are similar, so the loads are automatically copied,
but in my case, the roof level will be one kilometer per meter for the línea perimeter partitions.
So I will go to the construction levels.
I will modify the ground floor to be unique floor.
And I will check the debt load and the impulse load,
there's a mistake.
So now I modified old.
And it's not right as assumed.
Not to define the wind.
You can use the wind was OK and you get not that it's disabled yet because we haven't throw any wind
tunnels to receive the load.
So go to model type.
You have roof panel and wall panel.
I will choose one panel and I will draw on all the action that it will impose to untaught.
And the same way I will throw the roof panel.
And now I can run the windows up that will be corresponding to the selected code, I'm using the standard.
And now I will insert the parameters for my project.
And now the auction laws have been created and you can add more directions in case you have an irregular
plan and this project, I will delete the 270 and the 180 degree because I'm going to design the members
as a matter of members because the plan is almost regular and symmetric.
So in my case, it will be OK.
Now, from load up the one load, go to one of those cases, you can add it manually or you can generate
it automatically.
Now, from down below, you can see the old cases that have been defined, but you may see that there's
no laws assigned.
And that's because we have first to apply the wind, the decomposition, and now you can see it graphically,
if you can't see it, you can show it from the sea content because the other loads to see all the sign
laws and the direction of it.
Also, you can browse the wind loads and more details from the wind window and the right hand, you
can see the pressure zones, also the zero degree and the 90 degree.
You can see the roof zones and the war zones.
If you click and open the view, you can see all the details of the applied when gold.
You can choose, applied, lulled to see the values of the Lords and how it is distributed, the areas,
the pressure, also the conversions of the selected Lord.
Also, you can browse all directions that applied to the model.
Now, go to closing window and load cases, you can see the green mark, which means that this load
has successfully applied to the model cameras, all the loads.
And for the combination, you'll learn how to define it in the next video.
To the Lord case and the properties window, it's quite important that the total applied Lord will equal
the reaction.
That's how we assure that the distribution has successfully occurred.
You can sign the snow load using the snow, it insert all the cautions or the parameters that correspond
to your project.
However, in this project, I will consult the wizard and I will assign a uniform load manually.
I applied for the roof level.
Don't forget to choose the case before you assign the load to the model, I will choose the Lord and
the properties when I will insert the value of the Lord the direction, and I will choose now the roof
level.
And finally, press decomposition to transfer all those on slabs to supporting elements, and this is
the end of this video.