Hi, so let's continue with our course, and now we are going to create what we call the super elevation
and then we are going to create our longitudinal profile and then our profiles of cut and feel few related
to the terrain.
So first, the super elevation.
Let's learn how to create this view of our alignment and the.
OK, so let's do a zoom over here.
Let's select our alignment.
And in to be easier, you can click on this triangle over here, which will be the tangent.
I'm going to hit ESC now so you can see and I'm going to come here and OK, ready selected my my alignment
and noticed that when I select my alignment, look here on the top of the interface of the symmetry,
we have a new menu over here.
Look, alignment alignment, which is the name that I choose.
And in this ribbon, uh, we have a new super elevation.
We're going to click we have here calculate and it did super elevation.
I'm going to click one time.
And the software says the alignment doesn't contain data about super elevation.
What do you want to do?
Calculate it can calculate the super elevation now or I'm going to click it.
And now we can choose the type of road, um, I'm going to let the pivot method center based.
OK, this the line of the center of the road.
Let's remember that here is the kind of road, um, let's keep it undivided.
Um, OK.
And Lanes we're going to notice how interesting is this part.
We have the lanes over here and it is symmetric roadway.
Now if we mark it is already checked over here.
All that we sat in one side of the road, the software, we will replicate that to the left side.
So if I put here five mirrors, a change the other side to five, I'm going to come back here to six
and notice that softer right to change it to six.
And if I take away the symmetric roadway I can configure I can set each side differently with a different
configuration.
I'm going to keep the symmetric roadway.
We also have here the number of the lanes.
OK, I'm going to keep one and you can change.
OK, we'll have to wear the, uh, normal Leanna's lope.
OK, I'm going to keep it in minus two so you can change it according to a project.
I'm going to OK, I'm going to put four for normal in and ok then.
Clicking Finish.
Let's come here to show them control.
That's this calculate turns off because, uh, for now I don't want these columns in attainment here
in attainment can be kind of execution.
We have here according to the rate I mean the rate of relation between of our elevation.
I'm going to keep four percent.
OK, uh, we have the form from rolls of transition of the super elevation.
Um, this is very this is according to your project, OK, the percentage correspond to the tangent
for the curve.
OK, um, six six and.
The tangent curve, we also have the spiral curve.
So this is very particular of each project I'm going to keep it as this is a train meant learning,
OK?
And it is important for you to dominate the two so you can you can replicate according to your project.
I'm going to click finish and we here have the information about our Surber elevation.
And it's interesting to observe that we can modify all this information here if we just click, OK.
OK, so following I'm going to create the view, the visualization of this super elevation.
OK, so we already have our alignments selected.
Yeah.
I'm gonna, um, I'm going to check right here, OK, and we can click in super elevation and create
super elevation view.
I'm going to create this view.
We can this new window can change the name.
I'm gonna type superiorly vassil one, which is the same of super elevation, one you can choose by
name and following we can.
OK, let me see here.
Let's click.
OK, and we have to select here a place for Soft-hearted to create the super elevation.
OK, look, there are some inconsistencies uh, related to the calculus that need to be analyzed, but
it's it is not the focus of this treatment.
But it is important to notice the how the informations are being shown here.
Uh, the elevation since the zero.
OK, look, the percentages over here are limited and now we can go to create our longitudinal profile.
And what is that profile like?
We're seeing our terrain.
Like if we did did, uh, if we could it and we come to a cut and we're looking to our terrain from
the side.
OK.
So we can observe what needs to be modified on it, so in order to create our profile, we're going
to have to select our alignment.
OK, um.
Sorry, so we have our alignment over here and.
OK.
And notice that here on the top menu we have here, surface profile, uh, we also have a surface profile.
We have the profile view.
And so let's click in Surface Profile.
So we have the create profile from Surface, the sub software.
We create profile considering the surface of the terrain we just made.
And what's the idea here?
We have our terrain, the surface and the wild.
When we create this alignment, the software put this alignment right in the terrain, taking into consideration
the formations, the angles, the slopes, the variation of the terrain.
So that's the profile that is going to be created.
So now we have to add, um, in this new window, the earth's surface, uh, so the surface that we
created at a surface one we're going to select and click here.
It adds.
Okay, uh, we.
OK, we could the limited the range, uh, through this the profile, but so maybe you just want to
see the profile to the middle of it.
But I'm going to keep all and I'm going to click and draw draw in five view.
Just one click and we have this new window now and here we have, um, select alignment, we have al-Yemeni,
which was the alignment one.
OK, let's keep it corresponds to our alignment.
Uh, four, five, you name.
We can create a name.
I'm gonna type here a few longitudinal, uh, I mean profile.
One can add a description as usual in security.
We can always choose the style.
OK, the the graphics style of DOS profile here.
I'm going to select land.
OK, I'm going to click on Select Land Desktop where it is.
It landed desktop file view.
You're going to notice why I'm searching for OK here, why I'm searching for it.
Look, this is how it would be our visualization.
This is a preview, OK?
And before you create it, before you click in advance or create a perfect view, uh, let's go to your
menu.
Uh, notice that these menus on the left.
Let's click on Station Range here is almost the same idea.
We can select a range.
I mean, our limit.
So for the our visualization and I'm going to keep it as it is because I want to see the profile alignment
for fire in a hole, OK.
And, um, OK.
Uh, here and start and here in five you Heitz is the same idea to delimit, uh a range.
But here is concerning the elevation, the minimum and maximum.
I'm going to keep automatic because the software recognizes the terrain.
But you can uh I can click in user specified, uh, to change this range.
OK, um then don't have the profile display.
OK, data bands profile hatch.
I'm going to I'm, I'm not going to select anything here for life and let's click and create profile
view here on the bottom.
Uh, in order to create a profile for following the software asks us to click in a point of the screen.
So I'm going to click.
Here.
OK, here, it's good, and we have our five correspondents here, cosponsor zero, and he started,
OK, we started this elevation and it grows a little bit, OK from here, then it falls a little bit
and goes up again.
So this is our longitudinal profile.
So what what is going to be our next step now?
We are going to draw the profile.
Um, OK.
We have here the profile of our terrain and in this case, we're going to create a road.
So we are going to draw a new profile that would be this road, for example.
And to see the 3D will take into consideration the amount of URF that is going to be take it off the
terrain and the amount of earth that need to be added to the terrain.
OK, so
first we have to select our profile.
I'm going to click click here under here.
I'm sorry when I ask you select here, OK?
And, um, notice that here on the top we already have here for five of you if you wanted to join now.
And we have here profile creation tools, the tools that we're going to use.
Let's click once and will have this new window.
We can rename it here in name.
I'm gonna rename this our profile and perfume few.
I mean, profile one.
You can also add one description if you like.
Um, let's keep the profile style.
We have several options over here.
You can explore according to your interest.
Just let me check here.
Um, OK.
You can also change, um, the profile label sat here on the bottom.
Let's remember that the label are those informations that appear.
OK, so let's click, OK?
And now we need to do that with three D to take into consideration also the curves and the tangents.
So I'm going to ask an NAHJ, not select.
Our profile was created.
OK, I'm going to click on the left and draw tangents with curves.
OK, because now you're going to draw where, where will we be our road.
So let's remember that this points that I'm going to mark here that can be modified later.
And for example, I'm going to mark the first point here, OK?
And initial point.
I'm going to select the other points here.
OK, another one.
Over here and the next one or two to finish, OK, and all right, so see that the irad to have the
line of our terrain in in blue, we have what will be the creation of our roads.
OK, so it was already created.
I'm going to ask.
And when I click ask, we have here some elevation about our profile that was created and I want to
see as well the elevations in each point so we can click on the top menu, we can click on an option.
OK, here, profi, great view.
And look how interesting it is.
You can see here the three marks with some information.
Look, we have the PVI station, which are the points that are marked.
We have the PVI elevation, which are the elevations of the points, the points in blue line, which
is the route that I'm going to build.
And here we can modify the information.
OK, if you want the elevation of each point, what is that?
When I select one point, we can see a green triangle.
Look, I can see a green triangle in the profile identifying that point, um, so we can modify the
point marked here.
And what I want to show now is the terrain that is going to be taken off and the amount of earth that
need to be included over here.
Over here.
So I am going to.
OK, I'm going to select, I'm going to hide.
Select my blue line here and I'm going to, yeah, the profile grid view, I'm going to hide.
OK, so in profile here in profile, I prefer one, I'm going to click the right button actually hit
ask and you can select the whole border over here and right click.
Sorry, OK, right.
Click on it and can come in profile view properties, which are the properties of profile we created.
We are going to come here in on the top in bands and we are going to add OK, in this blank space over
here, what we want to see about the curtain feel of our terrain, the amount of earth that's going
to be taken off and what's going to be added.
So the band type, OK, we have the band type style.
You have the elevation.
This time, let's change the stage a few data.
OK?
OK.
And here in profile, I want to going to select superficial surface one in Profile Chugh, you're going
to select very important select profile one or perfume.
And we're going to.
Check these two boxes over here at label, service station and label and station.
OK, now we have already sat this part of my, uh, my profile as Phil and I got to add and want to
add a configuration here on the bottom related to the cut data.
OK, so I'm going to click OK, now cut the data.
I'm going to click in and you're gonna set the same conditions here, label start.
OK.
And just checking here, label start, already checked label and profi one seemed to be few, but of
profile one at select one.
Correct and just very fine and OK before clicking.
OK, let's come here to hatch and the lights clicking cut and feel I can click.
OK, and here we finally have the visualization and see we have the compensation in green.
What we need to add of material of earth.
Um and uh OK we have the terrain on the bottom, the red line and our road that is going to be created
in blue.
And this green patch is what is needed to be added at cut.
Cut is going to be in red like this.
Uh, OK.
The amount of urf and that in this class we finally finished the creation of our separate elevation,
our longitudinal profile and the cut and feel profile.
You're going to continue on our next class.